一、故障診斷?

1、 Fault diagnosis

當腹腔鏡出現故障送至維修中心，專業技術人員首先會與使用科室進行詳細溝通，了解故障發生的具體情形，如是否在手術過程中突然黑屏、圖像是否模糊、鏡頭是否存在霧氣等。隨后，運用專業檢測設備對腹腔鏡進行全面檢查，包括光學系統、電氣系統、機械結構等。例如，使用專用的圖像測試卡檢測鏡頭的成像質量，通過電氣檢測儀檢查線路是否存在短路或斷路情況。在這個過程中，技術人員憑借豐富的經驗和專業知識，對故障進行初步定位和分析。?

When the laparoscope malfunctions and is sent to the repair center, professional technicians will first communicate in detail with the department using it to understand the specific situation of the malfunction, such as whether the screen suddenly goes black during the surgery, whether the image is blurry, and whether there is fog on the lens. Subsequently, professional testing equipment was used to conduct a comprehensive examination of the laparoscope, including optical systems, electrical systems, mechanical structures, etc. For example, using a dedicated image testing card to check the imaging quality of the lens, and using an electrical detector to check for short circuits or open circuits in the circuit. During this process, technicians rely on their rich experience and professional knowledge to preliminarily locate and analyze faults. ?

二、拆解與清潔?

2、 Disassembly and Cleaning

確定故障部位后，技術人員會小心翼翼地對腹腔鏡進行拆解。由于腹腔鏡結構精密，內部零件微小且脆弱，每一個操作都需高度謹慎，稍有不慎就可能損壞零件。拆解完成后，對各個零部件進行深度清潔。對于光學鏡頭，使用專用的清潔劑和無塵擦拭布輕輕擦拭，去除表面的污漬、指紋和殘留的手術污染物；對于機械部件，采用超聲波清洗機進行清洗，利用超聲波的空化效應，清除部件縫隙中的污垢和雜質，確保清潔徹底。?

After identifying the fault location, technicians will carefully disassemble the laparoscope. Due to the precise structure of laparoscopy and the small and fragile internal components, every operation requires a high degree of caution, as even a slight mistake may damage the parts. After disassembly, thoroughly clean each component. For optical lenses, use specialized cleaning agents and dust-free wiping cloths to gently remove surface stains, fingerprints, and residual surgical contaminants; For mechanical components, ultrasonic cleaning machines are used for cleaning, utilizing the cavitation effect of ultrasonic waves to remove dirt and impurities from the gaps of the components, ensuring thorough cleaning. ?

三、零件修復與更換?

3、 Parts repair and replacement

根據故障診斷結果，對損壞的零件進行修復或更換。對于光學鏡頭的輕微劃痕，技術人員會采用專業的研磨和拋光技術進行修復，恢復鏡頭的透光性和成像清晰度；若鏡頭出現嚴重破損或無法修復的情況，則更換為原廠同規格的鏡頭。對于電氣線路的故障，如線路老化、接觸不良等，會仔細排查并更換損壞的導線或接頭；對于機械結構中的磨損部件，如密封環、彈簧等，及時進行更換，確保機械部件的正常運行和密封性。?

According to the fault diagnosis results, repair or replace the damaged parts. For minor scratches on optical lenses, technicians will use professional grinding and polishing techniques to repair them, restoring the transparency and imaging clarity of the lens; If the lens is severely damaged or irreparable, replace it with a lens of the same specifications from the original factory. For electrical circuit faults such as aging and poor contact, we will carefully investigate and replace damaged wires or connectors; For worn parts in mechanical structures, such as sealing rings, springs, etc., they should be replaced in a timely manner to ensure the normal operation and sealing of the mechanical components. ?

四、組裝與調試?

4、 Assembly and Debugging

在完成零件修復或更換后，按照嚴格的組裝順序將各個零部件重新組裝起來。組裝過程中，精確控制零件的安裝位置和緊固力度，確保各部件之間的配合精度。組裝完成后，對腹腔鏡進行全面調試。再次檢測光學系統的成像質量，調整焦距、白平衡等參數，使圖像達到最佳狀態；測試電氣系統的穩定性，檢查設備是否能正常啟動、運行，各項功能是否正常；對機械結構進行性能測試，如檢查鏡頭的旋轉、伸縮是否靈活順暢，器械通道是否暢通無阻等。只有通過所有調試環節，確保腹腔鏡各項指標符合標準后，才會進入下一個環節。?

After completing the repair or replacement of the parts, reassemble each component according to a strict assembly sequence. During the assembly process, accurately control the installation position and fastening force of the parts to ensure the precision of the fit between each component. After assembly, conduct comprehensive debugging of the laparoscope. Recheck the imaging quality of the optical system, adjust parameters such as focal length and white balance to achieve optimal image quality; Test the stability of the electrical system, check whether the equipment can start and operate normally, and whether all functions are normal; Conduct performance tests on mechanical structures, such as checking whether the rotation and extension of the lens are flexible and smooth, and whether the instrument passage is unobstructed. Only after ensuring that all indicators of the laparoscope meet the standards through all debugging steps, can we proceed to the next step. ?

五、質量檢測與驗收?

5、 Quality inspection and acceptance

維修后的腹腔鏡還需經過嚴格的質量檢測。使用專業的檢測設備對其進行全方位性能檢測，包括圖像分辨率、色彩還原度、亮度均勻性、電氣安全性等。同時，模擬手術環境進行實際操作測試，檢驗腹腔鏡在真實使用場景下的穩定性和可靠性。只有當所有檢測項目都合格，并經過使用科室的驗收確認后，維修后的腹腔鏡才會被重新投入臨床使用。

The repaired laparoscope still needs to undergo strict quality inspection. Use professional testing equipment to conduct comprehensive performance testing, including image resolution, color reproduction, brightness uniformity, electrical safety, etc. At the same time, simulate the surgical environment for practical operation testing to verify the stability and reliability of laparoscopy in real use scenarios. Only when all testing items are qualified and confirmed by the using department, will the repaired laparoscope be put back into clinical use.

本文由內窺鏡設備維修友情奉獻.更多有關的知識請點擊:http://wufangbu88888.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message